No sales in Florida after 9/30/22 due to state sales tax laws.  Any attempted orders will be cancelled.

I am in the process of retiring, the products shown will be the last.  Blackstone Arms in Texas is selling the 6.8 barrels and will take over the business.

DO NOT USE  bullets that are larger than .277" in these 6.8 barrels, 99.9% of all .270/6.8 bullets made are .277" diameter.  The chambers were designed for .277" bullets and all 6.8 barrels have a .277" bore so bullets larger than .277" will cause excess pressure and increased copper fouling.  It seems some Cavity Back bullets are .278" and on top of that they are solid copper so check the diameter of the bullets before using them. Same goes for 5.56/.223 bullets If they are larger than .224" do not use them. If .308 bullets are larger than .308" do not use them.

Enhanced strength 9310 alloy bolt, one of the most durable mil spec bolts on the market. Similar to JP Enterprise bolts. Mil spec parkerized rust resistant treatment(dark gray)   Flat rate shipping $3.75

Free shipping

If you are looking for a factory loaded AR  cartridge to hunt yotes, deer and hogs the 6.8 can't be beat in terminal performance. The exterior ballistics of the 6.8 and Grendel are within a few inches of each other all the way to 400yds. The 6.8 starts off 80-100fps faster with the same weight bullet and barrel length. The 6.8 has a great selection of usable hunting bullets. A 5.56 and a 6.8 could handle every possible need.

Hi perf. chamber and barrel allow for ANY factory ammo to be used along with the hottest handloads. The throat/freebore is designed to be more accurate with a wider range of bullets than the typical SPCII chamber.

• Chamber: 6.8ARP(similar to Wylde) accurized chamber
• Profile:  lightweight- tapers.750-700 under the guard/.750 gas block/.700 out front
• Fluted: No
• Barrel Length: 10.5"
• Twist Rate: 1:11- Hybrid 3R rifling
• Gas System: carbine Length
• Diameter at Gas Port: .750"--.078" port unless you direct otherwise on the order.
• Muzzle Thread Pitch: 5/8x24
• Material: 4150 Chrome Moly Vanadium Steel
• Finish: Melonite
• Process: Button Rifled
• Barrel Lining: Melonite
• Barrel Extension: M4
• Assembly: Stripped
• Weight: 1lb-3oz

.

For use on pistols or NFA registered SBR lowers only. All NFA rules apply.

Barrel purchased to test against ARP barrels, less than 100 rnds fired.

BCM® Exclusive Design

Continuous taper designed for optimal weight, balance, and performance on a semi-automatic carbine.

Heavier profile toward the rear near chamber area.

Thinner tapered profile out front.

No sharp handguard cap shoulder for improved barrel harmonics.
Approximate Weight: 1lb 5oz.

Please note for gas block selection, barrel journal measures .625"

4150 CMV, chrome lined bore-1lb 6oz

Apx 200 rounds fired, IWI 77gr Razor core  and S&B 77gr shoots aaround 1.5" at 100. Other military surplus ammo more like 2-2.5". Total length 26.5"

Have original box.

Sells for $1750-1799 new.�  $1400

Must ship to FFL for transfer.

Once fired Federal 6.8 SPC brass 100ct - shipped flat rate usps priority 7.95

Looks new, used as demo in shop. In original box with all parts and paper, warranty etc.

Like new in box with all parts and warrenty

USED 512 in box-  like new, mostly it has just been on a rifle sitting around the house but not used much.  I think these sell for 500 new.

night vision compatable

wide field of view

Uses AA batteries

HK (brand)91 surplus stock.  Will work on HK93 or HK91  but if used on a 91 only one pin will be used, the other will be uncovered.

These things are getting hard to find and are selling for $500 or more.

This flash hider is small diameter (.740) apx the same as a barrel diameter and very lightweight.  A very effective closed end flash hider that will not snag on branches etc.  Filmed from 2 ft in the dark side by side with the AAC Blackout and Smith Vortex, they reduced flash to a minimum glow where some devices and target crowned barrels produced a 10" ball of flame. None of the 4 flash hiders increased the noise to the shooter.
This flash does not need to be clocked and does not need a crush washer. If you want to clock the device you will need a crush washer.

For use with our 223 wylde barrels with 1/2-28 thread.

A very effective closed end flash hider that will not snag on branches etc.  Filmed from 2 ft in the dark side by side with the AAC Blackout and Smith Vortex, all of the 3 flash hiders reduced flash to a minimum glow where some devices and target crowned barrels produced a 10" ball of flame. None of the 3 flash hiders increased the noise to the shooter.
This flash does not need to be clocked and does not need a crush washer. If you want to clock the device you will need a crush washer.

For use with 6.5-6.8 calibers and smaller -barrels with 5/8-24 thread

A very effective closed end flash hider that will not snag on branches etc.  Filmed from 2 ft in the dark side by side with the AAC Blackout and Smith Vortex, along with our "Forked", all of the 4 flash hiders reduced flash to a minimum glow where some devices and target crowned barrels produced a 10" ball of flame. None of the 4 flash hiders increased the noise to the shooter.
This flash does not need to be clocked and does not need a crush washer. If you want to clock the device you will need a crush washer.

Silicone Magazine ID bands - pack of 4 -free shipping.

Choose caliber below.

TAC 30/ 30 Herrett-tan with black letters

30 Herrett--tan with black letters

5.56x42(NOT 5.56x45 or 223)--black with green letters

TAC 6---black w/red letters

Dies for the TAC 6 wildcat based on the 6.8 case.

+ actual shipping charges

3 boxes for $40+ 7.90 shipping charges

New Winchester 243 brass- bags of 50.  3 bags unprimed, 1 bag is primed.

JGreen email

Sells for $680

PressureTrace Internal Ballistics System

This is the interior ballistics portion of the RSI Shooting Lab system. It consists of pressure instrumentation and software that runs on a Windows PC. You must have access to a PC while using this product.

Barrel harmonic calculations are also provided when velocities are entered from a chronograph but a chronograph is not required for operation. PressureTrace II will work equally well with any good chronograph

 reserved .

Only available to those that have purchased a 270msr barrel in the past or purchasing one at the same time. Coupons not allowed, dies priced at cost plus shipping to help those that have purchased barrels.

Used side charge upper and carrier. Fits pretty sloppy in most lowers so will need to use the little rubber button under the back take down pin.

Works with standard mil spec barrel nut, not included

A set of 2 carbide chamber reamers, 1 rougher and 1 finish reamer. Chamber is a 277 Wolverine. A 5.56 necked up to .277. Carbide reamers are good for 400 chambers, these have cut 100.

1 carbide finish chamber reamer.  Carbide reamers are good for 400 chambers, these have cut 50. 

VLD reamer, throat setup better for VLD type bullets

A set of new carbide reamers, 1 rougher and 1 finish chamber reamer. Carbide reamers are good for 400 chambers, these have cut 0.

SRK(Search-Resue knife)- 6" blade Kray ex handle.

A popular knife with Military and Tactical Law Enforcement Personnel, the SRK is the standard issue knife of the Navy SEALS for their BUDS - or Basic Underwater Demolition training - the SRK has proved its worth time and time again in the most demanding environments.

New in box  $39+ $6 shipping.

Inpackage-FDE camo

150-200 best guess includes shipping

65 pcs of new Lapua brass, 2 boxes of CB bullets, 2 -10rnd mags, others bullets with count marked on boxes.

$100 shipped.

Carbide rougher and carbide finisher for the x42 cat.

port door and forward assist parts