Price:
    $0.01
    Items Remaining:out of stock

    NOTE- STAG, YHM and DPMS uses a different thread on their 6.8s than everyone else, our 5/8-24 thread comps will not fit their barrels we do not sell any muzzle device that will fit those barrels.

    The  Eliminator 5.56 brake is a full blown competition brake, it was designed with the priority being reducing the muzzle rise to zero along with reduced recoil for the fastest follow up shots while not being as loud as brake with large side ports. Do not use these brakes without hearing protection.

    The  Vortex Comp was designed to be quiet enough to hunt with out hearing protection for most. It reduces muzzle rise  apx 50% and recoil 30% . It does a great job at reducing flash.

    The "Shorty Brake" was designed for those that must use a pinned brake. The diameter is small enough that after pinned you can remove the gas block to work on your upper without destroying the brake. It is not a loud brake.

    Flash hiders are just that, they dissipate flash.  None of them do anything to reduce recoil or muzzle rise but they do not increase noise to the shooter.

    Noise to shooter least to most- for hunting without hearing protection stick with those in yellow

    Twisted Flash
    Shorty
    Vortex Comp

    Eliminator
     

    Reg. Price:
    $45.00
    Sale Price:
    $32.75
    Save:
    $12.25
    Items Remaining:out of stock

    This brake is designed to reduce recoil, keep excess noise down and allow owners to work on their rifles in states required to pin brakes. It is .720 diameter  so the gas block will slide over after it has been pinned, it only adds 5/8" to the length of the barrel.
    4 - 1/4" ports spaced evenly around the device, does not need to be clocked. A crush washer is not needed or included.
    This is an example of the raw machined brake only. They will be melonite treated black.

    Reg. Price:
    $54.00
    Sale Price:
    $49.69
    Save:
    $4.31
    Items Remaining:4

    A very effective closed end flash hider that will not snag on branches etc.  Filmed from 2 ft in the dark side by side with the AAC Blackout and Smith Vortex, along with our "Forked", all of the 4 flash hiders reduced flash to a minimum glow where some devices and target crowned barrels produced a 10" ball of flame. None of the 4 flash hiders increased the noise to the shooter.
    This flash does not need to be clocked and does not need a crush washer. If you want to clock the device you will need a crush washer.

    Reg. Price:
    $69.00
    Sale Price:
    $57.69
    Save:
    $11.31
    Items Remaining:12


    3 top  ports,  compensator with full twisted slot flash hider.
    Our quietest comp, offers great flash reduction  while keeping the muzzle down for a quick follow up shot.
    Closed end to keep from snagging on brush.
    Our own tests to find the one muzzle device that performs the best and is usable without hearing protection while hunting or on duty led us to the VC which has the most flash reduction while reducing recoil and controlling muzzle jump, and is the best all around choice for use without hearing protection.

    This comp does need to be clocked ports up with  a crush washer.
     

    Reg. Price:
    $45.00
    Sale Price:
    $32.75
    Save:
    $12.25
    Items Remaining:21

    This brake is designed to reduce recoil, keep excess noise down and allow owners to work on their rifles in states required to pin brakes. It is .720 diameter apx the same as the barrel diameter so the gas block will slide over after it has been pinned, it only adds 5/8" to the length of the barrel.
    4 - 1/4" slots (mod 1) spaced evenly around the device, does not need to be clocked. A crush washer is not needed or included.
    This is an example of the raw machined brake only. They will be melonite treated black to match the barrels.

    For use with .224 caliber and smaller with 5/8-24 threaded muzzles

    Reg. Price:
    $54.00
    Sale Price:
    $45.69
    Save:
    $8.31
    Items Remaining:13

    A very effective closed end flash hider that will not snag on branches etc.  Filmed from 2 ft in the dark side by side with the AAC Blackout and Smith Vortex, along with our "Forked", all of the 4 flash hiders reduced flash to a minimum glow where some devices and target crowned barrels produced a 10" ball of flame. None of the 4 flash hiders increased the noise to the shooter.
    This flash does not need to be clocked and does not need a crush washer. If you want to clock the device you will need a crush washer.

    For use with our 223 wylde barrels with 5/8-24 thread. SOCOM, 12.5, 18 and 20"

    Reg. Price:
    $69.00
    Sale Price:
    $52.50
    Save:
    $16.50
    Items Remaining:out of stock


    3 top  ports,  compensator with full twisted slot flash hider.
    Offers great flash reduction  while keeping the muzzle down for a quick follow up shot.
    Closed end to keep from snagging on brush.
    Our own tests to find the one muzzle device that performs the best and is usable without hearing protection while hunting or on duty led us to the VC which has the most flash reduction while reducing recoil and controlling muzzle jump, and is the best all around choice for use without hearing protection.

    This comp does need to be clocked ports up with  a crush washer, not included at this time.

    Fits 5.56/.223 caliber with 5/8-24 muzzle threads
     

    Reg. Price:
    $79.00
    Sale Price:
    $63.69
    Save:
    $15.31
    Items Remaining:out of stock

    Our best competition brake/muzzle control device - 10 -5/16" ports for 3 gun or multi gun competitors that wear hearing protection 100% of the time .  Melonite treated black to match the barrels.
    Machined from  8620 threaded  5/8-24 for our 5.56 Socom, 3gun and 20"  5.56 barrels only
    It reduces recoil more and has more muzzle control  than any other muzzle device we have tested for the fastest follow up shots possible.  .860 dia and 2" long

    Crush washer not included...not available at this time. 

    Reg. Price:
    $54.00
    Sale Price:
    $49.69
    Save:
    $4.31
    Items Remaining:4

    A very effective closed end flash hider that will not snag on branches etc.  Filmed from 2 ft in the dark side by side with the AAC Blackout and Smith Vortex, along with our "Forked", all of the 4 flash hiders reduced flash to a minimum glow where some devices and target crowned barrels produced a 10" ball of flame. None of the 4 flash hiders increased the noise to the shooter.
    This flash does not need to be clocked and does not need a crush washer. If you want to clock the device you will need a crush washer.

    For use with 6.8 calibers and smaller -barrels with 5/8-24 thread

    Reg. Price:
    $69.00
    Sale Price:
    $52.50
    Save:
    $16.50
    Items Remaining:out of stock


    2 top  ports for a little less noise and muzzle push down. Compensator with full twisted slot flash hider.
    Our quietest comp, offers great flash reduction  while keeping the muzzle down for a quick follow up shot.
    Closed end to keep from snagging on brush.
    Our own tests to find the one muzzle device that performs the best and is usable without hearing protection while hunting or on duty led us to the VC which has the most flash reduction while reducing recoil and controlling muzzle jump, and is the best all around choice for use without hearing protection.

    This comp does need to be clocked ports up with  a crush washer, not included at this time.

    Fits 6.8 caliber and smaller with 5/8-24 muzzle threads
     

    Reg. Price:
    $69.00
    Sale Price:
    $52.50
    Save:
    $16.50
    Items Remaining:9


    3 top  ports,  compensator with full twisted slot flash hider.
    Offers great flash reduction  while keeping the muzzle down for a quick follow up shot.
    Closed end to keep from snagging on brush.
    Our own tests to find the one muzzle device that performs the best and is usable without hearing protection while hunting or on duty led us to the VC which has the most flash reduction while reducing recoil and controlling muzzle jump, and is the best all around choice for use without hearing protection.

    This comp does need to be clocked ports up with  a crush washer, not included at this time.

    Fits 6.8 caliber and smaller with 5/8-24 muzzle threads
     

    Reg. Price:
    $54.00
    Sale Price:
    $45.69
    Save:
    $8.31
    Items Remaining:21

    A small .740 diameter version of our standard twisted fllash. Does a great job of dispursing flash without increasing noise to the shooter.

    Reg. Price:
    $45.00
    Sale Price:
    $32.75
    Save:
    $12.25
    Items Remaining:1

    This brake is designed to reduce recoil, keep excess noise down and allow owners to work on their rifles in states required to pin brakes. It is .720 diameter apx the same as the barrel diameter so the gas block will slide over after it has been pinned, it only adds 5/8" to the length of the barrel.
    4 - 1/4" ports spaced evenly around the device, does not need to be clocked. A crush washer is not needed or included.
    This is an example of the raw machined brake only. They will be melonite treated black to match the barrels.

    For use with 6.8  caliber and smaller with 5/8-24 threaded muzzles.

    Reg. Price:
    $54.00
    Sale Price:
    $45.69
    Save:
    $8.31
    Items Remaining:5

    A very effective closed end flash hider that will not snag on branches etc.  Filmed from 2 ft in the dark side by side with the AAC Blackout and Smith Vortex, along with our "Forked", all of the 4 flash hiders reduced flash to a minimum glow where some devices and target crowned barrels produced a 10" ball of flame. None of the 4 flash hiders increased the noise to the shooter.
    This flash does not need to be clocked and does not need a crush washer. If you want to clock the device you will need a crush washer.

    For use with 30 calibers and smaller -barrels with 5/8-24 thread

    Reg. Price:
    $45.00
    Sale Price:
    $32.75
    Save:
    $12.25
    Items Remaining:out of stock

    This brake is designed to reduce recoil, keep excess noise down and allow owners to work on their rifles in states required to pin brakes. It is .720 diameter apx the same as the barrel diameter so the gas block will slide over after it has been pinned, it only adds 5/8" to the length of the barrel.
    4 - 1/4" ports spaced evenly around the device, does not need to be clocked. A crush washer is not needed or included.
    This is an example of the raw machined brake only. They will be melonite treated black to match the barrels.

    For use with 30 cal  caliber and smaller with 5/8-24 threaded muzzles.

    Reg. Price:
    $69.00
    Sale Price:
    $52.50
    Save:
    $16.50
    Items Remaining:out of stock


    3 top  ports,  compensator with full twisted slot flash hider.
    Our quietest comp, offers great flash reduction  while keeping the muzzle down for a quick follow up shot.
    Closed end to keep from snagging on brush.
    Our own tests to find the one muzzle device that performs the best and is usable without hearing protection while hunting or on duty led us to the VC which has the most flash reduction while reducing recoil and controlling muzzle jump, and is the best all around choice for use without hearing protection.

    This comp does need to be clocked ports up with  a crush washer, not included at this time.

    Fits 30 caliber and smaller with 5/8-24 muzzle threads
     

      All Products made in America

      Beene Enterprises International
      PO Box 1981
      Morristown, Tn 37816

      The best way to contact is by email
      Email:  tech@ar15performance.com 

      Phone: 423-353-1107  8am-5pm eastern time  M-Thurs only

      We're in business for the working man.